Welcome to BRC Hobbies Call us on 0191 4887879

Manufact: Lemon

Product Description

Details

This is the new Lemon 10 channel 2.4GHz DSMX receiver.Lemon Receiver quality is guaranteed as all products have been tested to be compatible with Spektrum DSMX and or DSM2 products.All Lemon Receivers are full range including the Light series and in practice match or better the range of other comparable DSM2/DSMX receivers under the same conditions.Lemon receivers have the identification of connections,plug orientation and switch function printed on the PC board or the case.The Lemon RX Dual Antennas work by using independent processor that monitors the incoming signal and chooses the appropriate antenna for reception. This allows 2 different locations for installing the antennas along with different orientation. Satellite is no longer needed for receiver diversity which greatly reduces weight with increased overall reliability in comparison to the use of a primary receiver with satellite receiver.

Features:
* Compatible with DSMX aircraft radio and module systems
* FailSafe
* Diversity Antennas

Specification:
* Type:DSMX Compatible Full Range Receiver
* Number of Channel:10
* Modulation:DSMX Compatible
* Band:2.4 GHz
* Dimension:43mm x 34mm x 13.5mm
* Weight:12.5grams
* Voltage Range:3.45v - 7.2v

Binding Procedure
* Plug bind plug into receiver.
* Provide power to the esc and the LED will flash quickly.
* Enter bind mode on transmitter and ensure distance of 2 meters from receiver.A Solid LED light means binding is completed.
* Remove the bind plug.

Binding to Enable 11ms frame rate for high speed digital servo
* Insert  bind plug to the receiver bind port.
* Provide power to the unit.
* Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver.
* Remove bind plug.
* When the unit is powered quick flashing green light indicates 11ms frame rate is enabled.

Setting Failsafe
* Start by binding the receiver to the transmitter in the normal way.
* Ensure that transmitter and receiver are turned on.
* Insert bind plug into the receiver (Note: to set failsafe, bind plug is applied only when the receiver is turned on).
* Set transmitter controls to the desired failsafe positions.
* Press the side push button to memorize failsafe settings.
* Observe that the green light at the end of the receiver turns on to indicate failsafe is set. (Repeat step 4 will cause the LED to turn off which means failsafe is disabled).
* Remove bind plug.
* Disconnect the power for at least 2 seconds and then reconnect the power again.
* Test failsafe by turning off the transmitter.

HUART Output (High speed UART for UAV or quad-flying applications TX port (UART, 115200bps, 8N1)
* Condition 1 - UART output specification when no signal received (device reset and continuously monitors for valid signal roughly about every 0.5 sec):
- <0x13><'R'><'E'><'S'><'E'><'T'><0x13 
- <0x13> is used as header for beginning and ending identifier
* Condition 2 - UART output specification when signal is received ( updated  ~11ms with 2048/11ms DSM2 protocol with 12 bytes of information):
-<0x13><Throttle><Aileron><Elevator><Rudder><Gear><Aux1><Aux2><Aux3><Aux4><Aux5><0x13>
- DEC(0) ~ DEC(255) refer to the approximate value for each of the full range control output for the channels.
- <0x13> is used as header for beginning and ending identifier
For example: if all channels are centered except throttle shutdown and AUX is maximized, the UART should output the following.
<0x13><DEC(255)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><DEC(127)><0x13>

Note about Failsafe
* For Lemon Rx 10 channels receiver, failsafe is available for all channels and some users may find it useful (for robotics application or UAV).
* When bind plug is still plugged in after successful binding, pressing the (mem) button will cause the receiver to memorize all channel settings at the time the button is pressed for use in failsafe. If the failsafe is enabled correctly the green light should be on at the bottom of receiver. Press (mem) button again while bind plug is still plugged in will cause the green light to turn off. This indicate the failsafe mode is disabled.
* Remove bind plug before flying
* In the event of power disconnect, failsafe settings are still saved and will restore to set functions accordingly when power is provided.
* If you do not want to use failsafe, make sure green light is not on before flying

About failsafe enabled:
When the primary receiver and satellite receiver is unable to detect any RF signal for a continuous time interval of approximately 3 seconds, all channels will be restored to the saved setting. At this point the receiver will try to find valid RF signal. If valid signal is detected, the receiver will use the valid signal immediately.

IMPORTANT:
This is not a Spektrum receiver or design copy and is not supported by Spektrum or Horizon Hobby.The Spektrum, DSMX and DSM2 brand is a trademark of Horizon Hobby.This is not an underground black market fake Spektrum product. Lemon Receiver quality is guaranteed. Lemon Rx products are tested to be compatible with Spektrums DSMX and or DSM2 product. SpeKtrum, DS

 

Additional Information

Additional Information

SKU 406647
Weight 100.0000

Reviews

Write Your Own Review

Only registered users can write reviews. Please, log in or register

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.